最新天堂中文在线丨午夜嘿嘿嘿影院丨亚洲国产精品高清久久久丨中文字幕人成乱码熟女app丨www91亚洲丨97成人资源丨成人中文字幕+乱码+中文字幕丨一区二区三区在线 | 日丨日韩免费大片丨亚洲欧美一区二区三区丨国产在线观看a丨亚洲成人第一区丨国内免费视频成人精品丨亚洲综合色网站丨午夜精品美女久久久久av福利丨国产午夜人做人免费视频网站丨国产又黄视频丨97se狼狼狼狼狼亚洲网丨狠狠亚洲婷婷综合色香五月丨中国一级毛片黄丨国产女人十八毛片丨国产色视频在线播放丨国产亚洲精久久久久久无码苍井空丨天天摸日日摸爽爽狠狠丨久久综合香蕉国产蜜臀av

三菱FX2N有什么指令可BIT轉移給d寄存器值
及d寄存器值反轉BIT值回中號
d寄存器最大值不知能否到255（及反轉時）或者最大到?
比如
M0 = OFF，M1 = OFF，M2 = OFF，M3 = OFF <=>則D0 = 00
M0 = ON，M1 = OFF，M2 = OFF，M3 = OFF <=>則D0 = 01
M0 = OFF，M1 = ON，M2 = OFF，M3 = OFF <=>則D0 = 02
M0 = ON，M1 = ON，M2 = OFF，M3 = OFF <=>則D0 = 03
M0 = OFF，M1 = OFF，M2 = ON，M3 = OFF <=>則D0 = 04
M0 = ON，M1 = OFF，M2 = ON，M3 = OFF <=>則D0 = 05
M0 = OFF，M1 = ON，M2 = ON，M3 = OFF <=>則D0 = 06
M0 = ON，M1 = ON，M2 = ON，M3 = OFF <=>則D0 = 07
M0 = OFF，M1 = OFF，M2 = OFF，M3 = ON <=>則D0 = 08
M0 = ON，M1 = OFF，M2 = OFF，M3 = ON <=>則D0 = 09
M0 = OFF，M1 = ON，M2 = OFF，M3 = ON <=>則D0 = 10
M0 = ON，M1 = ON，M2 = OFF，M3 = ON <=>則D0 = 11
M0 = OFF，M1 = OFF，M2 = ON，M3 = ON <=>則D0 = 12
M0 = ON，M1 = OFF，M2 = ON，M3 = ON <=>則D0 = 13
M0 = OFF，M1 = ON，M2 = ON，M3 = ON <=>則D0 = 14
M0 = ON，M1 = ON，M2 = ON，M3 = ON <=>則D0 = 15
：
：

==========以下新增另一延伸問題==========
如果要"范圍單一M"(M0~M254)轉為D寄存器值或反轉BIT值回M
M0~M254只要一個沒有ON,則D0=0
M0=ON <=>D0=1
M1=ON <=>D0=2
M2=ON <=>D0=3
M3=ON <=>D0=4
M4=ON <=>D0=5
M5=ON <=>D0=6
M6=ON <=>D0=7
M7=ON <=>D0=8
M8=ON <=>D0=9
M9=ON <=>D0=10
M10=ON <=>D0=11
M11=ON <=>D0=12
M12=ON <=>D0=13
M13=ON <=>D0=14
M14=ON <=>D0=15
M15=ON <=>D0=16
:
M254=ON <=>D0=255
又有何指令支援

如果要"范圍單一M"(M0~M254)轉為D寄存器值或反轉BIT值回M
M0~M254只要一個沒有ON,則D0=0
M0=ON <=>D0=1
M1=ON <=>D0=2
M2=ON <=>D0=3
M3=ON <=>D0=4
M4=ON <=>D0=5
M5=ON <=>D0=6
M6=ON <=>D0=7
M7=ON <=>D0=8
M8=ON <=>D0=9
M9=ON <=>D0=10
M10=ON <=>D0=11
M11=ON <=>D0=12
M12=ON <=>D0=13
M13=ON <=>D0=14
M14=ON <=>D0=15
M15=ON <=>D0=16
:
M254=ON <=>D0=255
又有何指令支援

為何我用
DECO D0 M0 K8
DECO D0 Y0 K8
D0=0   ,Y0=ON  ,M0=OFF
D0=1   ,Y1=ON  ,M1=OFF
D0=2   ,Y2=ON  ,M2=OFF
D0=3   ,Y3=ON  ,M3=OFF
D0=4   ,Y4=ON  ,M4=OFF
D0=5   ,Y5=ON  ,M5=OFF
D0=6   ,Y6=ON  ,M6=OFF
D0=7   ,Y7=ON  ,M7=OFF
D0=8   ,Y8=ON  ,M8=ON
:( 以下D0=9~255;Y M皆可有對應ON)
:

但為何D0=0~7,則M0~M7 皆OFF

============
DECO D0 S100 K8
看來也可對應

不可對應M的原因找到了
我在M0~M7
前面各對應加了X0~X7 開關
作測試用
只是為何如此不行呢

引用

引用第8樓wayu于2019-01-15 13:46發表的  :
FX3U，Q都支持字的位訪問，不要用FX2N了

這位先進 你好

FX3U以前在用時沒注意到位這部份
不知你這位的訪問的使用是如何用
像歐姆龍的W或H類似三菱的M 可以用BIT
不知FX3U如何使用